Tektronix Technical Forums are maintained by community involvement. Feel free to post questions or respond to questions by other members. Should you require a time-sensitive answer, please contact your local Tektronix support center here.

Search found 11 matches

by brent_shen
May 11th, 2011, 7:21 am
Forum: 7000 Series Switch
Topic: Temperature Configuration
Replies: 2
Views: 12553

Re: Temperature Configuration

Hi Nathan,

Thank you for your reply. I found out that the single quotation mark (') around the key word TEMP are replace with a non-text-style single quotation mark when I copy and paste commands from the 2701 user manual. Now problem is solved.

Cheers,

Brent Shen
by brent_shen
May 11th, 2011, 6:46 am
Forum: 7000 Series Switch
Topic: How to Leave Scan Mode
Replies: 2
Views: 12933

How to Leave Scan Mode

Hi there, I successfully perform a scan on 8 channels. However, when the scan process ends and I was gonna measure a single channel (e.g. 102 for vdc), I got error 221 (Setting Conflict) and 215 (Arm Locking). Please tell me how to exit the scan mode back into normal single-shot measurement. Also, I...
by brent_shen
May 11th, 2011, 5:48 am
Forum: 7000 Series Switch
Topic: Temperature Configuration
Replies: 2
Views: 12553

Temperature Configuration

Hi there,

When I typed SENS:FUNC ’TEMP’,(@108) for Module 7708, I got the error message, "Invalid Character". Could you tell me what causes it? Also, this happened when no thermocouple attached to channel 108. Many Thanks.

P.S. Please email it to [email protected]

Sincerely,

Brent Shen
by brent_shen
April 13th, 2011, 8:12 am
Forum: 7000 Series Switch
Topic: Scan Settings
Replies: 1
Views: 10397

Scan Settings

Hi there, Could you verify the following code segment to scan 8 channels (dc voltage measurement on 101 to 107 and temperature measurement on 108)? Assuming only 7708 is installed in slot 1 of 2701 and tcpClient is a winsock object in VB. <Start of Code Segment> Line 01: tcpClient.SendData "*RST" & ...
by brent_shen
April 11th, 2011, 11:41 am
Forum: 7000 Series Switch
Topic: 2701 with 7708 & 7705
Replies: 3
Views: 15827

Re: 2701 with 7708 & 7705

Hi Dale, Thank you for your reply. Another related question for you. If I switch the previous two commands as follows 1) ROUT:MULT:CLOS (@201) ' Channel 201 of 7705 switches a built-in relay for some purpose; 7705 in slot 2 2) ROUT:CLOS (@101) ' Channel 101 of 7708 senses a dc voltage; 7708 in slot ...
by brent_shen
April 8th, 2011, 11:35 am
Forum: 7000 Series Switch
Topic: 2701 with 7708 & 7705
Replies: 3
Views: 15827

2701 with 7708 & 7705

Hi there, Assume that 2701 contains 7708 in slot 1 and 7705 in slot 2. If the following commands are entered remotely, 1) ROUT:CLOS (@101) ' channel 101 senses a dc voltage 2) ROUT:MULT:CLOS (@201) ' channel 201 switches a built-in relay of 7705 for some purpose My question: The command on line 2 sh...
by brent_shen
March 17th, 2011, 11:11 am
Forum: Cables and Connectors
Topic: Ethernet Cross-over Cable
Replies: 5
Views: 20027

Ethernet Cross-over Cable

Hi there,

Does 2701 come with an Ethernet cross-over cable?

Thanks

Brent
by brent_shen
March 9th, 2011, 8:29 am
Forum: 7000 Series Switch
Topic: Multiple Channel Operation
Replies: 1
Views: 10168

Multiple Channel Operation

Hi Dale,

Assume that 7708 is installed in slot 1 of 2701. If I type the following command,

1) ROUT:OPEN:ALL
2) ROUT:MULT:CLOS (@102,145)
3) ROUT:CLOS (@101)

Then, is channel 102 automatically open? or both channels 101 and 102 are closed?

Many Thanks

Brent Shen
by brent_shen
March 2nd, 2011, 7:24 am
Forum: Resistivity Measurements
Topic: Module 7708 Temperature Sensing
Replies: 1
Views: 9015

Module 7708 Temperature Sensing

Hi there,

Does Module 7708 support T-type thermocouple in addition to J and K type?

Thanks a lot

Brent Shen
by brent_shen
February 28th, 2011, 10:52 am
Forum: 7000 Series Switch
Topic: 7705-MTC-2 Cables
Replies: 1
Views: 10302

7705-MTC-2 Cables

Hi there, I saw Module 7705 come with the accessory of 50 Pin Male-to-Female DSUB cable (one end is 50 Pin Male connector and the other end is 50 Pin Female connector). I am gonna mount http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=206971-2-ND on my pcb board. Could you confirm if...
by brent_shen
February 25th, 2011, 10:43 am
Forum: 7000 Series Switch
Topic: Module 7705 Pin Assignment
Replies: 1
Views: 10273

Module 7705 Pin Assignment

Hi there,

I saw two 50-pin female D-sub connectors on the plug-in module 7705 (40-Channel Control Module). However, I just want to know the pin assignment and how the pins are related to the internal 40 channels. Many thanks.

P.S. Please email the answer to [email protected]

Brent Shen

Go to advanced search