Tektronix Technical Forums are maintained by community involvement. Feel free to post questions or respond to questions by other members. Should you require a time-sensitive answer, please contact your local Tektronix support center here.

Search found 8 matches

by CH2009
January 22nd, 2016, 1:43 pm
Forum: Series 2700 Multimeter/Data Aquisition/Switch System
Topic: Fast 4-wire resistance scan module for 2701
Replies: 1
Views: 10773

Fast 4-wire resistance scan module for 2701

Hello We have a dmm (2701 model) and we want realize a fast scan of 9 channels (all 4-wires resistance measurements). We have a 7706 module but we want to know if a faster module is available? In the current case, with the 7706 module, for one 4-wires resistance channel the duration is around 80ms (...
by CH2009
December 15th, 2015, 10:31 am
Forum: Series 2700 Multimeter/Data Aquisition/Switch System
Topic: Trigger (bus) after a complete scan
Replies: 1
Views: 10755

Trigger (bus) after a complete scan

Hello I have a DMM2701 with a multiplexing card 7706, my concern is that I would like to use the bus trigger to allow the dmm to perform another scan. First use a bus trigger which allow the dmm to perform a scan, then wait that all the scan is completed (several channels), read the data for the ent...
by CH2009
December 7th, 2015, 1:44 am
Forum: Series 2700 Multimeter/Data Aquisition/Switch System
Topic: DMM2701 Warm up for performance considerations
Replies: 1
Views: 10917

DMM2701 Warm up for performance considerations

Hello,

For performance considerations, the documentation we can read that it must be allowed to warm up the model 2701 for at least 2 hours. My question is: can we check how long the model is turned on (date and time)? Can we use SCPI command to retrieve this information?

Thanks in advance
by CH2009
November 27th, 2015, 9:29 am
Forum: Series 2700 Multimeter/Data Aquisition/Switch System
Topic: synchronize NPLC around zero of 50Hz power line
Replies: 1
Views: 10742

synchronize NPLC around zero of 50Hz power line

Hello,

I have a question about NPLC configuration for a dmm 2701 using a multiplexing card 7706. I would like to know if it is possible to perform a measure with NPLC inferior to 1 and centered around zero of 50Hz power line?

Thanks in advance
by CH2009
November 3rd, 2015, 9:42 am
Forum: 2450/2460 Touchscreen SourceMeter
Topic: problem with linear dual sweep
Replies: 2
Views: 13136

Re: problem with linear dual sweep

Hello, Thanks for your answer. We use the DMM 2701 (with multiplexing card 7706) to measure the voltage sourced by the SMU2450 in addition to other parameters we need (for exmaple 4W resistance, and temperature from thermocouple). The voltage range on the DMM2701 is configured to 10V. We already set...
by CH2009
October 31st, 2015, 4:51 am
Forum: 2450/2460 Touchscreen SourceMeter
Topic: problem with linear dual sweep
Replies: 2
Views: 13136

problem with linear dual sweep

Hello We recently bougth a SMU2450 and we noted a problem with the linear dual mode. In the framework of our experiment, we want to generate different steps of voltage which are then amplify by a power amplifier toward our setup. When we configure the SMU to source a linear dual sweep from -10mV to ...
by CH2009
October 14th, 2015, 10:56 am
Forum: DMM7510 Graphical Sampling DMM
Topic: Secondary Measurements from DMM7510
Replies: 2
Views: 13989

Re: Secondary Measurements from DMM7510

Thanks for your reply and this information.
by CH2009
October 13th, 2015, 11:11 am
Forum: DMM7510 Graphical Sampling DMM
Topic: Secondary Measurements from DMM7510
Replies: 2
Views: 13989

Secondary Measurements from DMM7510

Hello,

I would like to know how use the secondary measurements from a DMM7510. Is it possible to measure simultaneously (or alternatively from switch mode) temperature from a thermocouple and a voltage? how to plug the two separate DUT to the DMM?

Thanks in advance

Go to advanced search