Tektronix Technical Forums are maintained by community involvement. Feel free to post questions or respond to questions by other members. Should you require a time-sensitive answer, please contact your local Tektronix support center here.

Trigger Configuration to Measure CE Sat Voltage

Models 2601, 2602, 2611, 2612, 2635, 2636
Models 2601A, 2602A, 2611A, 2612A, 2635A, 2636A
Models 2601B, 2602B, 2604B, 2611B, 2612B, 2614B, 2634B, 2635B, 2636B
Post Reply
jaime_g
Posts: 93
Joined: September 23rd, 2014, 6:14 am
Country: United States

Trigger Configuration to Measure CE Sat Voltage

Post by jaime_g » March 1st, 2017, 2:59 pm

I am trying to measure the Collector-Emitter Saturation Voltage of an NPN transistor. The Vce drops from 10V to ~0.2V when the transistor is in its saturated state. To achieve saturation a 1.55mA, 500µs pulse is applied to the base terminal with the collector bias voltage set at 10V. An SMU21612B is used to source the pulse on channel A and measure the saturation voltage on channel B.

I am not able to come up with the correct commands to configure channel B measurement trigger. I would appreciate any suggestions on the commands I should use to accomplish this task.

Here is the code i am using:

Code: Select all

reset()
display.screen = display.SMUA_SMUB[attachment=0]CE Saturation Voltage.png[/attachment]
display.smua.digits = display.DIGITS_4_5
display.smub.digits = display.DIGITS_4_5
smua.sense = smua.SENSE_REMOTE
smub.sense = smub.SENSE_REMOTE

-- Configure base current source
smua.source.autorangei = smua.AUTORANGE_OFF
smua.source.rangei = 10e-3
smua.source.leveli = 0
smua.source.limitv = 5

-- Configure collector voltage source
smub.source.autorangev = smub.AUTORANGE_OFF
smub.source.rangev = 10
smub.source.levelv = 10
smub.source.limiti = 10e-3

-- Configure collector Sat voltage measure
smub.measure.nplc		= 0.001
smub.measure.autorangev = smub.AUTORANGE_OFF
smub.measure.rangev = 1
smub.measure.autozero = smub.AUTOZERO_ONCE

-- Configure base current 500µs pulse width
trigger.timer[1].delay = 480e-6
trigger.timer[1].stimulus = smua.trigger.ARMED_EVENT_ID
trigger.timer[1].count = 1
trigger.timer[1].passthrough = false

-- Configure collector Sat voltage measurement trigger
trigger.timer[2].delay = trigger.timer[1].delay - 200e-6
trigger.timer[2].stimulus = trigger.timer[1].EVENT_ID
trigger.timer[2].count = 1
trigger.timer[2].passthrough = false

smua.trigger.arm.count = 1
smua.trigger.count = 1
smub.trigger.arm.count = 1
smub.trigger.count = 1

-- Enable base current pulse source trigger
smua.trigger.source.stimulus = smua.trigger.SWEEPING_EVENT_ID
smua.trigger.source.action = smua.ENABLE
smua.trigger.source.listi({1.55e-3})
smua.trigger.source.limitv = 5

-- Enable CE Saturation Voltage measurement trigger
smub.trigger.measure.stimulus = trigger.timer[2].EVENT_ID
smub.trigger.measure.action = smub.ENABLE
smub.trigger.measure.v(smub.nvbuffer1)

-- Return to 0V after pulse is complete
smua.trigger.endpulse.stimulus = trigger.timer[1].EVENT_ID
smua.trigger.endpulse.action = smua.SOURCE_IDLE

smua.source.output = smua.OUTPUT_ON
smub.source.output = smub.OUTPUT_ON
smua.trigger.initiate()
waitcomplete()
print(smub.measure.v(smub.nvbuffer1))
smub.source.output = smub.OUTPUT_OFF
smua.source.output = smua.OUTPUT_OFF
Here is the oscilloscope trace:
Attachments
CE Saturation Voltage.png
CE Saturation Voltage.png (9.9 KiB) Viewed 7470 times

Post Reply

Return to “2600 Series SourceMeter”

Who is online

Users browsing this forum: Bing [Bot] and 5 guests